English translation for "error amplifier"
|
- 偏差放大器
误差放大器
误差信号放大器
Related Translations:
- Example Sentences:
| 1. | A novel error amplifier with initial voltage reference for series voltage regulator
串联稳压器基准误差放大电路的设计 | | 2. | In order to design the parameter of error amplifier , the small signal model is derived for arc welding inverter using state - space averaging , and frequency - domain analysis is performed to complete the parameter design
为了设计控制系统中误差放大器的参数，利用状态空间平均法建立了电源系统的低频小信号数学模型，进而利用控制理论中的频域分析法设计了系统的补偿网络，即误差放大器的参数。 | | 3. | The whole circuit consists of a multiplier , an error amplifier , a comparator , a rs flip - flop , an and gate , and an inverter , etc . . the electronic circuit simulator cadence is utilized to practice the detailed functional simulation of the general circuit and the subsystem circuits
整个电路由模拟乘法器、误差放大器、比较器、 rs触发器、与门和倒相器等基本单元电路组成，采用工作站上的大型ic设计软件cadence进行仿真。 | | 4. | In meantime , the all sub - circuits are also designed and emulated carefully including error amplifier , voltage reference circuit , voltage comparator , rs type flip - flop , soft - start circuit , sawtooth - wave generator , pwm comparator , current added circuit and so on
其次对控制器内部芯片的各个模块误差放大电器、自举电流电路、电压基准源、电流求和电路、 rs触发器和驱动电路等模块进行了具体的设计和仿真的逻辑功能做了解释。 | | 5. | Some sub - block circuits ( error amplifier , soft - start , enable comparator and under - voltage protection circuit ) are designed and several electrical characteristics are simulated using hspice . finally , the whole chip performance is simulated . and the results show the satisfaction to both function targets and characteristics
在子电路设计中,本论文只对其中的误差放大器、软启动电路、使能比较器和欠压保护四个子电路进行了电路原理分析与设计,并在此基础上,运用eda软件hspice对各功能模块的各项指标、参数进行了仿真、分析。 | | 6. | In the thesis , some of the most important functional modules of the pwm power control ics are designed and simulated , including error amplifier , voltage reference , voltage regulator , comparator , and oscillator . the topologies , schematics and layouts of some circuits are introduced and developed
本毕业设计研究和提出了构成pwm电源控制芯片的主要功能模块，设计了其中主要模块ip核的多种结构电路并进行了仿真，完成了部分电路的版图设计? ?包括误差放大器，基准电压源，电压调节器，比较器，振荡器等。 | | 7. | And then , based on the above theories , the circuit design and simulation means have been concretely applied in the internal modules of voltage reference , bias circuit , oscillator , error amplifier and drive circuit of the chip and so on . the relevant design indexes are successfully achieved . at last , the whole circuit simulation and layout design are completed
在此理论基础上对该电源芯片内部的各个模块,如电压基准源、偏置电路、振荡器、误差放大电路和驱动电路等模块进行了具体的电路设计和分析仿真,且达到了相应地设计指标,最后,完成了整体电路仿真和版图设计。 | | 8. | Subcircuit models are designed and simulated , which includes bias current source , voltage reference , error amplifier , pwm comparator , driver circuit , protection circuits for over - temperature , over - current . at last , combined with periphery component , the circuit is simulated , and the result meets the anticipant requirement
并对集成电路内的各个模块包括电流偏置电路、基准电压电路、误差放大电路、三角波振荡发生电路、 pwm比较电路、驱动电路、过热保护电路和过流保护等进行了具体的设计和仿真,并对整体应用电路进行了仿真,结果均达到了预先设定的指标。 | | 9. | In the meantime , the all sub - circuits are also designed and emulated carefully including inverter , rs type flip - flop , voltage reference circuit , error amplifier , voltage comparator , sawtooth - wave generator , pwm comparator , soft activation circuit and so on . as a result , all of the sub - circuits answer the requirements . this chip has taped out with the 0 . 5um mix - signal process of csmc
本文利用cadenceeda集成电路设计工具、 spectres仿真工具,对集成电路内的各个模块包括反相器、基本rs触发器、基准电压电路、误差放大电路、电压比较电路、锯齿波振荡发生电路、 pwm比较电路、软启动电路、驱动电路等进行了具体的设计和仿真,且达到了预先设定的指标。 | | 10. | The synchronous rectifying and low power sampling technology is used to reduce the power consumption , flexible external loop compensation , error amplifier output clamp are adopted for better system large signal response . the piecewise slope compensation technology is employed to minimize the consequence of over compensation . the sensor resistor is externally connected , which realize output voltage programmable . the overheat protection and under voltage protection modules are integrated in the die to allow the reliable operation of the system
同时,电路设计采用同步整流技术、低功耗电流采样技术降低功耗,提高转换效率;采用灵活的外部环路补偿技术、误差放大器输出嵌位技术以实现良好大信号特性;采用分段斜坡补偿技术,消除不稳定因素,并最大程度地减小过补偿带来的问题;采用外接输出采样电阻的方式,实现输出电压的可编程。 |
- Similar Words：
- "error alert program" English translation, "error allowance" English translation, "error am" English translation, "error ambiguity" English translation, "error amount" English translation, "error an" English translation, "error analysis" English translation, "error analysis facility" English translation, "error and omission" English translation, "error and omission claim" English translation
|
|
|
